Thursday, November 17, 2011

Expert Tips for Using Stained Glass Grinders

Once you’ve finished cutting your glass pieces, the next step is grinding and smoothing the edges in preparation for foiling and fitting them together. Stained glass grinders make the grinding easier and quicker, but they do present some issues for inexperienced users. These tips from pros can help beginning users of stained glass grinders get a good handle on using their new equipment.

Grind Against the Rotation for Deeper Cuts

On most stained glass grinders, the bit rotates counter-clockwise. If you want to do deeper cuts in the glass, push your glass piece in the opposite direction – that is, from right to left. If you want more control and shallower cuts, push your glass against the bit in the same direction as the turn.

Experiment with Scrap Glass Before You Work with Your Pieces

Every type of glass will grind a little differently. It all depends on the thickness and fragility of the glass, as well as its texture and the shape. Before you start grinding on a new project, get a feel for how the glass grinds by practicing a bit with scraps. That will give you a feel for how much pressure you can use without chipping the edges of the glass.

Always Protect Yourself from Glass Chips and Dust

Eye protection is a must when you’re working with stained glass grinders -– glass chips and glass dust flies everywhere. If your grinder doesn’t have a protective face shield, wear goggles.

Don’t Forget Your Fingers

Glass edges are sharp. Protect your fingertips while you’re grinding with this pro tip for using stained glass grinders. Wrap surgical tape around and over your index fingers and thumbs to protect them from cuts and snags.

Keep the Sponge Wet and the Reservoir Full

It’s important to keep your glass wet while you’re grinding. Keep half an eye on the water level in the water reservoir and make sure that the sponge stays wet.

Troubleshooting Chipped Glass

The biggest issue that most beginners have with glass grinders is chipped edges on their glass. There are a number of reasons this can happen, and the right cure depends on the cause.

Thin or delicate glass can chip if you press too hard against the grinder bit. Try easing back a bit to see if that helps.

A coarse grinding bit can chip more delicate glass as well. Try using a finer grade bit.

A worn bit can also cause chipping, even on heavy-duty glass. Check your bit carefully for worn spots and replace it if necessary.

Finally, the shaft on your grinder may be warped or off center – it’s not typical, but it can happen with an older grinder. If that’s the case, you’ll need to replace the grinder with a new one.

Stained glass grinders will make your work much smoother, more professional and easier. It takes a little effort to get the knack of working with them, but the effort is more than worth the results.

Sunday, November 13, 2011

Stained Glass Grinders and Other Smoothing Tools

Do you really need stained glass grinders to create stained glass art? Some of the most beautiful stained glass mosaics in the world were created before the discovery of electricity, so quite obviously, glass grinders aren’t essential to the art of creating stained glass pieces. On the other hand, stained glass grinders can make your work easier and give you more finished and professional results.

Creating beautiful pieces of stained glass artwork takes a lot of time, planning and sheer, tedious elbow grease. Using the best stained glass tools can help cut down the tedium and increase your enjoyment in your work. If you’re a novice glass worker, your workshop should have a handful of basic tools for cutting, shaping and smoothing glass pieces.

Glass Cutting Tools

The primary tool of the stained glass artist is the glass cutter – a lubricated carbide wheel that scores and cuts through glass. There are many types of glass cutters on the market, including those that are specially designed for people who have hand strength or hand grip problems. You’ll also find specialized glass cutting tools to help you cut clean straight edges and curves.

A glass saw can also be useful for doing intricate work. In general, they’re slower to use than a glass cutter, but may be the perfect solution for thicker glass or for patterns that require inside curves and intricate shapes.

Glass pliers are a necessity for making clean breaks and cuts, and for snipping away small edges or pieces.

Tools for Smoothing Glass

A carborundum stone is a rough stone designed to sand the edges of glass smooth so that the pieces fit together precisely. This precision fit is vital to making stained glass pieces that are as strong as they are beautiful. A carborundum stone costs about $10, which is considerably less expensive than even the cheapest glass grinders, but you’ll be spending hours buffing and smoothing glass edges by hand. Other manual smoothing tools include emery cloths and diamond files.

A glass grinder reduces the amount of work required to smooth the edges of your cut glass pieces. The best glass grinders also provide ways for you to do other things. A grinder that can hold a variety of bits, for example, may allow you to drill holes through glass with a fine bit, or to texture the surface of glass or shape glass beads.

You can buy an inexpensive glass grinder for around $50, but most stained glass artists recommend starting choosing from the intermediate range of stained glass grinders that offer more flexibility and options for expansion.